How Do I Turn Up My Invisible Fence Collar

via

How do I change the intensity on my petsafe collar?

With the Receiver Collar turned on, press and release the Mode Button briefly. When released, the unit will flash indicating the Correction Level by the number of times the indicator flashes. Press the mode button again within 5 seconds of the last red flash and it will increase one level. via

How do I make my pet safe collar stronger?

Trim your pet's hair where the Contact Points touch his neck. Increase the Static Correction Level. Repeat training steps to reinforce training. Purchase a stronger Receiver Collar by contacting the Customer Care Center at 1-800-732-2677. via

How do I check the battery in my Invisible Fence collar?

  • Remove your pet's receiver collar from your pet.
  • Take the collar to the boundary area of your containment system and listen for the collar to beep.
  • If the collar beeps or the test light tool illuminates, the battery and collar are working.
  • via

    How do you reset an Invisible Fence transmitter?

    System reset can be as simple as replacing the batteries in the transmitter. Bring your dog inside and turn off the power at the door. Disconnect the transmitter. Look for metal objects around or above the fence. via

    Why does my PetSafe collar not work?

    Take battery out of the collar for several minutes and replace it with new battery. Make sure battery is installed properly. Make sure the tab within the battery housing unit is making good contact. If receiver collar still does not activate – remove a wire from the transmitter, try to change the levels. via

    How do I reset my pet safe collar?

  • Remove the receiver collar from your pet.
  • Remove the battery from the receiver collar.
  • At the transmitter, move the boundary switch from the low to the high position.
  • Slowly adjust the boundary control dial up to #8, down to #1 and then back to the #4 position.
  • via

    How long do PetSafe collars last?

    It should last 3-4 years. via

    How can I make my invisible fence stronger?

  • Push the button on the receiver. A light on the receiver will flash.
  • Adjust the distance from the boundary wire to trigger a warning alarm. Most transmitter boxes have a knob or lever to use to change the distance.
  • Change the metal prongs on the receiver.
  • via

    Why is my PetSafe collar beeping but not shocking?

    My receiver collar is beeping but my pet is not responding to the static correction. Remove the collar from your pet. Make sure the static correction level on the receiver collar is set at 2 or above. Take the test light tool and place it on the receiver collar and walk out to the boundary of the containment system. via

    Why is Invisible Fence bad?

    Here's why using an invisible underground electric fence is not a good idea: While an electric fence may look invisible, its damaging effects are very visible, and generally increase harmful behavior over time. Dogs can become fearful or even aggressive because they are being hurt. via

    Do Invisible Fence collars wear out?

    The collar runs on batteries, which, of course, will eventually wear out, but even if you are meticulous about checking on the functioning of your system, some dogs learn to outsmart it. An invisible fence collar delivers shocks through two prongs that need to be in close contact with the skin. via

    What does it mean when Invisible Fence collar flashes green?

    The status light will double flash green every 30 seconds during the 24-hour period after the dog has entered the boundary area. Once the receiver detects that the battery has reached a low voltage level, the status light will change from the normal blinking “green” every 30 seconds to blinking “red” every 10 seconds. via

    What does flashing red light mean on Invisible Fence collar?

    Why is my Invisible Fence collar blinking red? If you have started to see a red flashing light on your pet's Computer Collar unit, your Power Cap battery may need to be replaced. Your fence will still work, but if your power goes out, the system will no longer be operational until power is restored. via

    How long do Invisible Fence batteries last?

    Invisible Fence® Brand Computer Collar® units are powered by a specially designed 3-Volt Lithium Power Cap® battery that Canine Company recommends replacing every 3 months to ensure continuous and trouble-free operation of your dog's Computer Collar. via

    How do you reset an electric dog collar?

    Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal. via

    How do I test my petsafe collar?

    The Test Light Tool is used to tell if your collar is working properly. Hold the tool against the contact points and activate the collar. For a remote trainer, activate the correction using the transmitter. For a fence, move the collar near the boundary, holding the collar at your dog's neck height. via

    Why does my shock collar not work?

    Proper fit is crucial for the e-collar to have any impact on your dog. If BOTH contact points are not touching the dog's skin, the dog will not perceive any sensation at all. This happens because the collar is on the dog too loose. If the e-collar is easily rotating around the dog's neck, it is too loose. via

    How do I know if my shock collar is working?

    Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working. via

    Leave a Comment

    Your email address will not be published. Required fields are marked *